Classics Rescue: Basic Carb and Ignition Tweaks Tame a Bucking Shelby Cobra

21:41  13 november  2017
21:41  13 november  2017 Source:   HOT ROD

Former Shelby employees plan continuation 1965 Shelby GT350R

  Former Shelby employees plan continuation 1965 Shelby GT350R The iconic racing Mustang, with some improvements.The project is being overseen by the Original Venice Crew, made up of former Shelby America employees Peter Brock, Jim Marietta and Ted Sutton.

HOT ROD Rescue : Basic Ignition and carb Tweaks restore driveability on a wild Shelby Cobra ’s 418-Windsor with no need for major drivetrain changes. Bill Stockdale’s 1967 Shelby Cobra replica is powered by a built Ford 351 Windsor–based motor stroked out to 418 ci.

Rescue : Basic Carb and Ignition Tweaks Tame a Bucking Shelby Cobra . Ignition timing is like seasoning: some is good, but too much ruins the results. Bumping…

The Combo

Shelby is Building Six New Big-Block Daytona Coupes

  Shelby is Building Six New Big-Block Daytona Coupes Shelby American will build six aluminum continuation big-block Daytona Coupes to the original specifications of the car that could have dominated Le Mans.Shelby American has announced plans to build six Daytona Coupes with 427-cubic-inch big block engines as part of an official continuation series. The company brought the first of six, CSX2603, to the Rolex Motorsports Reunion at Monterey this past weekend, where it made its public debut.

We experienced all four Shelby Mustang variants, including the Ford Mustang Shelby GT, Shelby GT EcoBoost, and stick and auto Super Snakes. Rescue : Basic Carb and Ignition Tweaks Tame a Bucking Shelby Cobra .

Rescue : Basic Carb and Ignition Tweaks Tame a Bucking Shelby Cobra 8 November, 2017.

Research

Research

Bill Stockdale's 1967 Shelby Cobra replica is powered by a built Ford 351 Windsorbased motor stroked out to 418 ci. The 10.2:1 engine is equipped with free-flowing Edelbrock Victor aluminum heads and a fairly stout Isky hydraulic roller cam ground on a 110-degree lobe-separation angle (LSA), with 0.544/0.573-inch valve lift and 238/248 degrees duration at 0.050-inch tappet lift. Torque flows through a Tremec TKO five-speed/overdrive manual trans back to an independent rear suspension (IRS) based around a 3.27:1-geared Ford 8.8-inch centersection with Traction-Lok.

The Problem

It's a cool car, but all that jerking around kind of takes the fun out of it." — Bill Stockdale

When Stockdale purchased the car from the previous owner, it had a severe fuel leak as well as clutch issues. After they were fixed by a local shop, Stockdale says, "Through the gears at full throttle, the car ran like a scalded dog—no hesitation when you stand on it, no bogging or stumbling. The car will scream!" Unfortunately, at part throttle, "Anytime the engine gets below 1,800 to 2,000 rpm, it bucks and jerks as if you were in Fourth gear and going too slow—like just before you slow to a stop without downshifting. You have to constantly be tipping the throttle in any gear and keep the rpm over 1,800. I never get out of Third gear in the city."

GM wants positive relationship with feds as ignition-switch oversight ends

  GM wants positive relationship with feds as ignition-switch oversight ends This all stems from the GM ignition switch recall.In May 2014, GM paid $35 million to the Department of Transportation in civil penalties and agreed to three years of monitoring. That was followed in 2015 with a $900 million fine from Department of Justice. Part of the terms of the fine meant that GM had a federal overseer with access to employees, records, and meetings.

HOT ROD Rescue : Basic Ignition and carb Tweaks restore driveability on a wild Shelby Cobra 's 418-Windsor with no need for major drivetrain changes. Rescue : Basic Carb and Ignition Tweaks Tame a Bucking Shelby Cobra .

blog 'jennguzman.blogdetik.com' is not exists. Taming Our Monkey Mind: Insight, Detachment, Identity eBook.

Band-Aiding the problem, one shop replaced the Holley 750-cfm HP carb with a smaller 650-cfm unit. At this point, Stockdale says the Cobra would "idle good, but kind of rich. I pulled the [spark] plugs and they were pretty black, so we went up two heat ranges on the plugs and went down 10 jet sizes in the carb—all without any real change. The shop told me, 'This is just the way the car is and I should be happy with it.' I have had a lot of performance cars over the years, and none of them ever acted like this.

"I don't know if the cam is just too big for the street, if the fuel system isn't set up right, or what. I've looked for vacuum leaks, but haven't found any. I would think that a vacuum leak would result in an inconsistent idle, but the idle is stable. I put on a new set of spark plug wires—still no change. I backed the timing down 10 degrees—no change. I'm out of ideas."

The Diagnosis

0104] Swap and tune carburetor

The tenth Shelby G.T. 350 built was an advanced prototype

  The tenth Shelby G.T. 350 built was an advanced prototype "It came to us in 2014 from a private collector," Dale Spahr tells us. Dale and business partner Tony Conover sell their share of primo Shelbys through their business, Performance Motors of Hanover, Pennsylvania. With 35 years of Shelby restoration experience, Dale and Tony knew that upon arrival to their shop, this Shelby was something special. Its condition was superb, but beyond that, its history was extraordinary. If today you could go back and write any history for a Shelby, it would be hard to top this one. Research ford mustang See All Model Years See Pricing Officially, it is SFM5010, an advanced prototype '65 G.T.

blog 'jorgezivolich.blogdetik.com' is not exists. The taming of the wild : BLMs wild horse and burro adoption program (SuDoc I

blog 'davebrazington.blogdetik.com' is not exists. To Tame a Highland Warrior (Highlander, Book 2) eBook.

0515] Tune or replace distributor

1617] Fresh Autolite spark plugs

18] Chassis-dyno test

As received at a local Ohio tuner facility, the spark plugs were black, indicating an overall rich mixture. There were no vacuum leaks, and cranking cylinder compression was OK. An initial run on the chassis dyno replicated Stockdale's complaint. The higher the gear, the worse the problem was. Assuming the engine is internally sound, a driveability issue like Stockdale's is often the result of a carburetor and/or ignition problem.

Here, the smaller 650 carb turned out to be a poor fit for the 418ci engine. Trying to make it work, someone had jetted the primaries way too rich, and they were still way rich even with Stockdale's claimed 10-size lean-out. On the other hand, the 650 was dangerously lean upstairs. Anytime you have to go up or down more than about a half-dozen jet sizes, it's usually a clue something else is off. In this case, to achieve a stable idle with a big cam and small carb, the curb idle screw may have been turned too far in, excessively uncovering the throttle-plate transfer slot to prematurely activate the main system. When that happens, the curb-idle mixture screws lose adjustment authority.

Ford Confirms 2019 Mustang Shelby GT500 With Over 700 HP

  Ford Confirms 2019 Mustang Shelby GT500 With Over 700 HP A brand new teaser from the Blue Oval says the super Shelby will return in 2019. It seems Ford is pulling out all the stops for its Mustang fans ahead of the 2018 Detroit Auto Show. Hot on the heels of a new Mustang Bullitt now comes an official teaser for the new Shelby GT500 Mustang, shown both on Ford’s Facebook page and YouTube account. Research 2018 ford mustang See Full Specs See Pricing The video appears to be computer rendered, showing a current-generation Mustang with serious hood louvers, and honking big spoiler, and a promise of over 700 horsepower.

blog 'sherrybrown.blogdetik.com' is not exists. Low Carb Paleo, Allergy Free, Dairy Free and Gluten Free Recipes (Paleo Diet

blog 'sherrygrieve.blogdetik.com' is not exists. Pistenbully Comes To The Rescue (PistonBully Series) eBook.

On the ignition side, the Cobra was running a Ford large-cap Duraspark magnetic-impulse distributor, circa 19751985. Like GM's HEI, it was made during the Nader (ha!) of engine performance, a time of strict emissions standards but before "the computer" arrived to restore driveability. In stock form, these "smog" distributors tend to have wacky centrifugal advance curves plus excessive amounts of spark-ported vacuum advance that was restricted by various analog switches and devices, generally limiting the amount of advance in the lower gears. These curves are not suitable to an emissions-exempt, performance engine with relatively high compression and a healthy cam.

One shotgun approach is changing out the 3.27:1 rear gears for a set of 3.90:1 or 4.10:1 gears, but on the other hand the lightweight Cobra combined with the TKO's steep First gear could make it amenable to ironing out the problem with just carburetor and ignition tweaks.

The Fix: Carb

The 650 carb's rich idle problem could have been overcome by fine-tuning its replaceable primary-side air-bleeds, but on the whole the carb was still on the small side for achieving the 418 engine's full top-end potential. As it was still available, the best overall move in this case was putting Stockdale's original, larger, Holley 750-cfm HP carb back on, then properly adjust and calibrate it. The first thing was setting the curb-idle mixture. Everyone seems to have their own pet method for adjusting a high-end Holley carb's four-corner idle-mixture screws. In this case, the tuner backed out (richened) all four idle mixture screws from their lightly bottomed position a little at a time to achieve the highest engine idle rpm. When idle stability got reasonably close, final idle-quality adjustments were primarily made on the primary screws, with slight richening as needed to help tune out any residual bucking. Basically, a "cut-and-try" procedure. The car now idled smoothly (well, as smooth as a lumpy cam can get) at 925 to 950 rpm, where before it wasn't happy below 1,000 rpm.

World’s largest collector car auction takes place in Florida

  World’s largest collector car auction takes place in Florida Over 3,000 collector cars to cross the block in Florida The classic cars to buy now before it’s too late

blog 'robertbartsch.blogdetik.com' is not exists. Rescue Team (Grace Medical) epub pdf txt.

blog 'allisonfox.blogdetik.com' is not exists. Real Kids Real Adventures #8: Apartment Fire, Trinity River Rescue

With idle quality stabilized, the big carb required only slight main-jet changes. The primaries were leaned by five numbers (from No. 79 to No. 74); the secondaries needed slight richening (from No. 84 to No. 85). Finally, Holley jet extensions were also installed on the secondary side to prevent uncovering the jets when fuel sloshes to the rear of the float bowl under hard acceleration.

The Fix: Timing

Running on unleaded pump premium gas, this hot rod Ford liked about 36 degrees of total timing, all in by 3,200 rpm. The final installed curve ended up with 16 degrees of base (initial) timing, and 10 degrees of centrifugal advance in the distributor, starting at 2,100 rpm and all in by 3,200 rpm. Remember, the distributor rotates at half the crank speed, so the amount of advance in the distributor is doubled as read at the crank: 16 degrees initial on the balancer + (10 degrees distributor 2) = 36 degrees on the balancer. The vacuum advance was not connected; it's just too erratic for an engine and chassis of this caliber.

["06-Ford-Duraspark-bending-tab-changes-curve-rpm-start-point"]

06] Bending the tab (circle) on the Duraspark alters the rpm point where the centrifugal advance starts: inboard brings the curve in sooner at a lower rpm; outboard delays curve initiation to a higher rpm because it effectively stiffens the springs.

["07-Ford-Duraspark-advance-springs-and-weights-location"]

07] But altering the curve's advance-rate and total amount of advance requires major unit disassembly, as the slotted plate and springs are located beneath the breaker plate. The two ways to do this are "out-of-motor" or "on-motor."

1966 Shelby 427 Cobra S/C Sells at $2.94 Million at RM Sotheby’s Scottsdale

  1966 Shelby 427 Cobra S/C Sells at $2.94 Million at RM Sotheby’s Scottsdale Preston Tucker’s Tucker 48 is runner up at $1.79 millionAs bidding fell flat at $9.8 million on Saturday evening, it became clear that the reserve would not be met, leaving RM Sotheby's high sales award with the '66 Shelby 427 Semi-Comp Cobra and its $2,947,500 winning bid, some half-million dollars over the top estimate. Semi-comp Cobras are rare—the result of Carroll Shelby converting left-over competition cars for street use, after failing to meet FIA homologation requirements.

blog 'russellquenzer.blogdetik.com' is not exists. Taming the Star Runner ebook by S. E. Hinton.

blog 'randybenge.blogdetik.com' is not exists. Basic Accounting eBook.

Other than slightly altering the centrifugal advance initiation threshold, putting a full centrifugal curve in a Ford OE-style distributor is a major pain in the butt because the centrifugal-advance mechanism is hidden inside the bowels of the distributor.

Whether in or out of the car, major disassembly is required; even experts take about 45 minutes every time they make a curve alteration.

Once you gain access, recurving kits to change the advance rate are available from Mr. Gasket and Crane Cams; the latter also includes an adjustable vacuum advance can in addition to lightweight springs

Changing the total amount of centrifugal advance may require custom mods, depending on which advance plate is in the existing distributor.

The Fix: MSD

If this sounds like way too much work, MSD has a better idea with its Pro-Billet Ford extra-duty standalone distributor. Access its GM-style, centrifugal-advance mechanism and stop bushing by merely removing the cap and rotor—about a 5-minute job. A curve similar to the Ford unit can be constructed by using one heavy silver spring, one light silver spring, and a purple bushing. On the downside, the MSD unit costs around $500 at Summit Racing, but quality and performance doesn't come cheap. You get what you pay for.

The Fix: Spark Plugs

The final fix was replacing Stockdale's fouled spark plugs with a fresh set of Copper-Core Autolite projected-tip resistor plugs. Stockdale already had a premium MSD ignition coil.

The Results

Basic ignition and carb tuning eliminated the low-rpm, part-throttle buck—without going to steeper rear gears. After the tune-up, the fat torque curve generated by the now smoothly running engine maintained 400+ lb-ft of corrected rear-wheel torque over a 1,400-rpm range starting at approximately 2,900 rpm. On the top-end, corrected power at the rear wheels was more than 390 hp from 5,200 through 5,600 rpm.

Ferrari, Cobra worth $4 million found in condemned NC garage

  Ferrari, Cobra worth $4 million found in condemned NC garage Just imagine the reaction of the person who discovered them The post Ferrari, Cobra worth $4 million found in condemned NC garage appeared first on Motoring Research. Follow MSN Autos on Facebook and Twitter

blog 'randyhussain.blogdetik.com' is not exists. Ignition Handbook: Principles and Applications to Fire Safety Engineering

Lessons Learned

Talk about driving down the wrong road! Every Band-Aid laid over the Cobra's wounded driveability only made things worse. Big cams tend to reduce low-end torque, making proper carburetor and ignition tuning critical. It appears Stockdale's part-throttle troubles sort of evolved (or devolved) from the new clutch. As we've seen in past rescues, clutch-release characteristics can affect overall driveability at low rpm. For those of us on a budget (and who isn't?), careful basic tuning on a street car may do away with the need for major parts changes. Don't be a parts swapper—be a parts fixer!

Need Junk Fixed?

If your car has a gremlin that just won't quit, you could be chosen for Hot Rod to the Rescue. Email us at pitstop@HotRod.com and put "Rescue" in the subject line. Include a description of your problem, a photo, your location, and a daytime phone number.

Contacts

Autolite, a Division of FRAM Group IP LLC (Rank Group Ltd.); Lake Forest, IL; 855.200.5200; Autolite.com

Crane Cams; Daytona Beach, FL; 866.388.5120 or 386.310.4875; CraneCams.com

Ford Parts—Motorcraft Parts; Dearborn, MI; 800.392.3673; FordParts.com or Motorcraft.com

Holley Performance Products; Bowling Green, KY; 800.HOLLEY1 (nearest dealer), 866.464.6553 (tech), or 270.782.2900 (general); Holley.com

Mr. Gasket (A Holley Brand); Bowling Green, KY; 866.464.6553; Holley.com/brands/mr_gasket/

MSD Performance (A Holley Brand); El Paso, TX; 888.258.3835 (toll-free), 915.857.5200 (general); or 915.855.7123 (tech); MSDperformance.com

Ferrari, Cobra worth $4 million found in condemned NC garage .
Just imagine the reaction of the person who discovered them The post Ferrari, Cobra worth $4 million found in condemned NC garage appeared first on Motoring Research. Follow MSN Autos on Facebook and Twitter

—   Share news in the SOC. Networks
This is interesting!